| | SIMATIC DP, ET 200ECO PN, 8 DO DC 24V/1,3A; 4 X M12, DOUBLE-ASSIGNEMENT, DEGREE OF PROTECTION IP67; |
| |
| General information |
| Vendor identification (VendorID) | 002AH |
| Device identifier (DeviceID) | 0306H |
| Supply voltage |
| Load voltage 1L+ |
| Rated value (DC) | 24 V |
| permissible range, lower limit (DC) | 20.4 V |
| permissible range, upper limit (DC) | 28.8 V |
| Reverse polarity protection | Yes |
| Load voltage 2L+ |
| Rated value (DC) | 24 V |
| permissible range, lower limit (DC) | 20.4 V |
| permissible range, upper limit (DC) | 28.8 V |
| Reverse polarity protection | Yes |
| Input current |
| from load voltage 1L+ (unswitched voltage) | 4 A |
| from load voltage 2L+, max. | 4 A |
| Power losses |
| Power loss, typ. | 5.5 W |
| Digital outputs |
| Number/binary outputs | 8 |
| In groups of | 4 |
| Functionality/short-circuit strength | Yes; Electronic |
| Response threshold, typ. | 1.8 A |
| Limitation of inductive shutdown voltage to | Typ. (L1+, L2+) -47 V |
| Switching capacity of the outputs |
| on lamp load, max. | 5 W |
| Controlling a digital input | Yes |
| Output current |
| for signal "1" rated value | 1.3 A; Maximum |
| for signal "0" residual current, max. | 1.5 mA |
| Parallel switching of 2 outputs |
| for increased power | No |
| for redundant control of a load | Yes |
| Switching frequency |
| with resistive load, max. | 100 Hz |
| with inductive load, max. | 0.5 Hz |
| on lamp load, max. | 1 Hz |
| Aggregate current of outputs (per group) |
| all mounting positions |
| up to 55 °C, max. | 3.9 A |
| up to 60 °C, max. | 2.6 A |
| Cable length |
| Cable length unshielded, max. | 30 m |
| Interfaces |
| Transmission procedure | 100BASE-TX |
| Transmission rate, max. | 100 Mbit/s |
| Supports protocol for PROFINET IO |
| Number of PROFINET interfaces | 2 |
| Autocrossing | Yes |
| Automatic detection of transmission speed | Yes |
| Integrated switch | Yes |
| PROFINET IO Device |
| IRT with the option "high flexibility" supported | Yes |
| Prioritized startup supported | Yes |
| Protocols |
| Supports protocol for PROFINET IO | Yes |
| Protocols (Ethernet) |
| SNMP | Yes |
| DCP | Yes |
| LLDP | Yes |
| ping | Yes |
| arp | Yes |
| Interrupts/diagnostics/status information |
| Status indicator | Yes; Green LED |
| Alarms |
| Diagnostic alarm | Yes |
| Diagnostic messages |
| Diagnostic functions | Yes |
| Diagnostic information readable | Yes |
| Monitoring the supply voltage | Yes; Green "ON" LED |
| Wire break in actuator cable | Yes |
| Short circuit | Yes |
| Group error | Yes; Red/yellow "SF/MT" LED |
| Galvanic isolation |
| between the load voltages | Yes |
| between load voltage and all other switching components | No |
| between Ethernet and electronics | Yes |
| Galvanic isolation digital outputs |
| between the channels | No |
| Permissible potential difference |
| between different circuits | 75 VDC / 60 VAC |
| Isolation |
| tested with |
| 24 V DC circuits | 500 V |
| Interface | 1500 V; According to IEEE 802.3 |
| Degree and class of protection |
| IP65 | Yes |
| IP66 | Yes |
| IP67 | Yes |
| Connection method |
| M12 | Yes |
| Dimensions |
| Width | 30 mm |
| Height | 200 mm |
| Depth | 49 mm |
| Weight |
| Weight | 550 g |
| Status | Mar 12, 2012 |
