| | SIMATIC S7-1200 POWER MODULE PM1207 STABILIZED POWER SUPPLY INPUT: 120/230 V AC OUTPUT: 24 V DC/2.5 A |
| Technical specifications | |
| Product | S7-1200 PM1207 |
| Power supply, type | 24 V/2.5 A |
| Input | |
| Input | 1-phase AC |
| Supply voltage / 1 / at AC / nominal value | 120 V |
| Supply voltage / 2 / at AC / nominal value | 230 V |
| Voltage range | |
| | Automatic range selection |
| Input voltage / 1 / at AC | 85… 132 V |
| Input voltage / 2 / at AC | 176… 264 V |
| Wide-range input | No |
| Overvoltage resistance | 2.3 × Vin rated, 1.3 ms |
| Mains buffering at Iout rated, min. | 20 ms |
| Mains buffering | at Vin = 93/187 V |
| Rated line frequency | 50/ 60 Hz |
| Rated line range | 47... 63 Hz |
| Input current / at nominal level of the input voltage 120 V | 1.2 A |
| Input current / at nominal level of the input voltage 230 V | 0.67 A |
| Switch-on current limiting (+25 °C), max. | 13 A |
| Duration of current limiting / at 25 °C / maximum | 3 ms |
| Inrush current A²s | 0.5 A²·s |
| Built-in incoming fuse | T 3,15 A/250 V (not accessible) |
| Protection in the mains power input (IEC 898) | Recommended miniature circuit breaker: 16 A, characteristic B, or 10 A, characteristic C |
| Output | |
| Output | controlled, isolated DC voltage |
| Rated voltage | 24 V |
| Total tolerance, static ± | 3 % |
| Static mains compensation, approx. | 0.1 % |
| Static load balancing, approx. | 0.2 % |
| Residual ripple peak-peak, max. | 150 mV |
| Spikes peak-peak, max. (bandwidth: 20 MHz) | 240 mV |
| Product feature / output voltage adjustable | No |
| Output voltage setting | - |
| Status display | Green LED for 24 V OK |
| On/off behavior | No overshoot of Vout (soft start) |
| Startup delay, max. | 6 s |
| | 2 s at 230 V, 6 s at 120 V |
| Voltage rise, typ. | 10 ms |
| Rated current value Iout rated | 2.5 A |
| Current range | 0… 2.5 A |
| delivered active power / typ. | 60 W |
| short-term overload current / at short-circuit during run-up / typical | 6 A |
| Duration of overloading ability for excess current / on short-circuiting during the start-up | 100 ms |
| short-term overload current / at short-circuit during operation / typical | 6 A |
| Duration of overloading ability for excess current / on short-circuiting during the operational phase | 100 ms |
| Parallel switching for enhanced performance | Yes |
| Numbers of parallel switchable units for enhanced performance | 2 |
| Efficiency | |
| Efficiency at Vout rated, Iout rated, approx. | 83 % |
| Power loss at Vout rated, Iout rated, approx. | 12 W |
| Closed-loop control | |
| Dynamic mains compensation (Vin rated ±15 %), max. | 0.3 % |
| Dynamic load smoothing (Iout: 50/100/50 %), Uout ± typ. | 3 % |
| Load step setting time 50 to 100%, typ. | 5 ms |
| Load step setting time 100 to 50%, typ. | 5 ms |
| Setting time / maximum | 5 ms |
| Protection and monitoring | |
| Output overvoltage protection | < 33 V |
| Current limitation, typ. | 2.65 A |
| Characteristic feature of the output / short-circuit protected | Yes |
| Short-circuit protection | Constant current characteristic |
| Enduring short circuit current / Effective level / typical | 2.7 A |
| Overload/short-circuit indicator | - |
| Safety | |
| Primary/secondary isolation | Yes |
| Potential separation | Safety extra low output voltage Vout according to EN 60950-1 and EN 50178 |
| Protection class | Class I |
| stray current / maximum | 3.5 mA |
| CE mark | Yes |
| UL/CSA approval | Yes |
| UL/cUL (CSA) approval | cULus-Listed (UL 508, CSA C22.2 No. 107.1), File E197259; cURus-Recognized (UL 60950-1, CSA C22.2 No. 60950-1) File E151273 |
| Explosion protection | ATEX (EX)
|
